Products

Reeds for original factory reed block with carbon membranes. These cause less damaged to the engine should the reed petals break up than metal alte...

Adjustable carburettor needle with clip.

Air cut-off valve. This valve sits on the side of the carburettor and richens the mixture somewhat to avoid the engine running too lean. Needle is ...

Air cut-off valve. This valve sits on the side of the carburettor and richens the mixture somewhat to avoid the engine running too lean.

Licenced replica of the English Amal carburettor from Arreche. Available in various sizes. 16mm easy to tune for standard cylinders and tuned 50cc ...

Licenced replica of the English Amal carburettor from Arreche. Available in various sizes. 16mm easy to tune for standard cylinders and tuned 50cc ...

Licenced replica of the English Amal carburettor from Arreche as replacement or tuning item. Fits the original intake manifold. Compact design allo...

Licenced replica of the English Amal carburettor from Arreche, as cheap original replacement or tuning item. Fits the original intake manifold. Com...

Arreche is a Spanish carburettor manufacturer that is licenced to produce English Amal replica units. Great value for money, for all 2-stroke engin...

Arreche is a Spanish carburettor manufacturer that is licenced to produce English Amal replica units. Great value for money, for all 2-stroke engin...

Licenced replica of the English Amal carburettor from Arreche, as cheap original replacement or tuning item. Fits the original intake manifold. Com...

Screw for air cut-off valve and choke plate.

Plastic carburettor cap for all GY6 4-stroke 50cc scooters 139 QMB/QMA

Screw for plastic carburettor cap with collar.

Dellorto 17.5 mm carburettor. For scooters with Minarelli or CPI engines. Recommended even for untuned engines, as the carburettor is easier to tun...

Dellorto 17.5 mm carburettor. For scooters with Minarelli or Minarelli-based engines. Recommended even for untuned engines, as the carburettor is e...

Dragster racing technology. The venture (funnel-shaped) air ducts optimize the airflow to the carburettor and accelerates the volume of air being t...

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Carburettor diaphragm for original carburettors fitted to the Chinese imported 4 stroke scooters with the 139QMA/QMB. This said, there are still nu...

Float bowl gasket for Keihin PWK carburettor.

Rubber float bowl gasket for all original and Naraku NK200.01 carbs for GY6 50cc engines 1239 QMB/QMA.

Metal float bowl with accelerator pump. Suitable for all original and Naraku NK200.01 carbs for GY6 50cc engines 129 QMB/QMA.

Float bowl screw with locking ring.

Standard Naraku carburettor floats for GY6 50cc 139 QMB/QMA.

Float bearing pin.

Float needle valve.

Aftermarket carburettor for all 2-stroke scooters with 1E40QMB engines. Minarelli replica air-cooled. Comes with electric choke. Note: In rare case...

Good quality 17.5mm carburettor from Naraku for Piaggio engines. Great alternative to those expensive top end brands with no compromise on quality...

Cost-effective 17.5mm carb from Naraku for Minarelli and Minarelli-based engines (Chinese versions) and horizontal Peugeot engines. Leaves nothing ...

Naraku V.3 carburettor 18.5mm for 50cc 4-stroke scooters. Top quality at an affordable price. No start issues as with Chinese alternatives and good...