ATU Explorer

The following description is generated automatically by Google Translation Service. The MHR is the exhaust from Malossi MHR specially on the cylind...

Malossi 4 reed racing reed block. 0.3mm thick reeds give great power when used with the Malossi Big Valve blocks. Malossi offers 2 additional membr...

Speed Belt by Polini. This v-belt features an aramid weave that makes it elastic and highly durable. Without doubt, one of the best v-belts in our ...

Malossi MHR intake manifold with short opening and straight connection. 22/24.5mm variant has a 22mm opening and a 24.5mm carb carb connection 19-2...

High-quality, but cost-effective aftermarket piston for original cylinders from Italian piston specialists Meteor. The set contains a piston, gudge...

High-quality, but cost-effective aftermarket piston for original cylinders from Italian piston specialists Meteor. The set contains a piston, gudge...

Malossi reinforced counter pressure torque spring - yellow = super strong

Reeds for original factory reed block with carbon membranes. These cause less damaged to the engine should the reed petals break up than metal alte...

Polini Air Speed variator pulley, great upgrade for the original due to design producing increase cooling. Suitable for 16mm shafts only.

Naraku carburettor repair kit for 50-90cc carbs. Comes with adjustable needle, needle clip, 80 main jet, pilot jet, float bowl gasket, idle jet, mi...

Airsal cylinder head 70cc [T6-Racing] - CPI, Keeway E2

Airsal cylinder gasket set for 50cc [T6-Racing] - CPI, Keeway E2

Piston ring set Airsal 50cc [T6-Racing] - CPI, Keeway E2

Airsal piston kit 50cc [T6-Racing] - CPI, Keeway E2

Airsal cylinder head 50cc [T6-Racing] - CPI, Keeway E2

Set of 3 sliders for Malossi Multivar variators. Sliders should be replaced to avoid damage. Not suitable for Piaggio MHR variators.

Malossi MHR Team exhaust system, specially tuned for the Team cylinder. Clean torque and great power deliver. Very good low down torque that you do...

Naraku Sports Contra Spring V.2 +1500rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

Naraku Sports Contra Spring V.2 +1000rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS hose clamp - 139QMB/QMA

Oil plug gasket for 139QMB/QMA.

SLS [secondary air system] gasket - 139QMB/A

Oil strainer bolt O-ring - 139QMB/QMA

Timing chain tensioner gasket for 139QMB/QMA.

Cylinder head gasket [50cc = 39mm] - GY6 50cc

This gasket sits in the valve cover in an identical metal plate and seals the crankcase breather. For valve covers with and without SLS.

Right-hand crankcase gasket - GY6 50cc

Mid-crankcase gasket. This gasket seals the left and right hand sides together. Required when changing the crank or completely splitting the cases.

Gasket for the gearbox cover on GY6 50cc 4-stroke engines.

The Tecnigas Next-R suitable for GY6 50cc 4-stroke and 4-stroke engines Kymco. This exhaust has a good energy yield with relatively low sound. In t...

Some scooters are sent from the factory with two rear shock absorbers. These models mostly use aluminium exhaust systems. These are generally mount...

Oil pump and drive gear for Chinese-built 4-stroke GY6 50ccm 139QMB/QMA engines. This item fits the 22 tooth version. This gear has 47 teeth.

SLS with hose for GY6 50cc exhaust systems with SLS. Often this part is necessary if the mounting bolts have rusted or locked, or the engine is run...

Naraku unrestricted Racing CDI with improved/advanced mapping for 50cc 4-Stroke Chinese imported scooters. Perfect CDI unit for tuning requirements...

Complete valve cover with connector for 50cc GY6 and Kymco 4-stroke engines. The valve cover is ready to install and supplied as shown. The valve c...

Little end bearing for 12mm gudgeon pin. This size is generally found on CPI, Keeway, Mawi, Longija, Generic engines etc. from 2003 on, as well as ...

139QMB/QMA engines currently have 2 crank variations factory-fitted. The differences are solely in the oil pump drive gear. The crank can be kitted...

Standard brake shoes. Also included: 2 new springs. Performance and construction as per original item. Dimensions: 110mmx25mm For rear drum brakes ...

Naraku Torque Driver with 2 different linear guide slots. Most torque drivers have curved slots which is not ideal for performance gains but fine f...

V.2 is the latest version of the CNC-machined pulley from NARAKU. This enhanced version now allows you to mount the original variator fan wheel and...

Electronic 25kmh scooter restrictor kit. Includes all necessary parts for installation and the parts certificate and instruction manual are include...

Aluminum Kickstarter [Light] in carbon look suitable for Minarelli and Peugeot engines.

Aluminum Kickstarter [Light] suitable for Minarelli and Peugeot engines.

The Naraku HS-Racing is a well-engineered High Speed variator for Minarelli-based 2-stroke engines with a 16mm tail shaft. The variator comes with ...

Brake light switch for rear disc brakes on GY6 50/125/150cc Chinese-built scooters with rear disc brakes.

Repair kit for Chinese GY6 139QMB/QMA original carburettors. Comes with adjustable needle, needle clip, main jet, pilot jet, float bowl gasket, idl...

Replacement aftermarket clutch bell. Already blued clutch bells tend mean slipping and deforming of the plates. This means the bell cannot run true...

Variator back plate.