Generic

Dellorto PHBG 21mm carburettor are the optimal carbs up to racing level. Great design and fine tolerances make this carb easy to tune. Whether in t...

Racing carburettor technology for the track with the Malossi MHR Team VHST carb kit. Kit contains: filter, reed block, inlet rubbers, MHR flange, d...

Malossi all-in-one MHR carburettor set with suitable filter, pre-configured for MHR cylinders. 26mm is the optimal variant for high end cylinders. ...

Malossi MHR Malossi Sport flow-optimized reed block with carbon reeds. MHR carbon reeds give better responsiveness. Thickness: 0.3mm. Different thi...

Malossi flow-optimized reed block with carbon reeds. Carbon reeds give better responsiveness. Thickness: 0.3mm. Different thicknesses affect the en...

Malossi full cheek racing crank for Minarelli AM, Generic, KSR-Moto, Keeway, Motobi, Ride, CPI, 1E40MA, 1E40MB engines. RHQ (Racing High Quality) f...

In ARTEK crankshaft bearing sets high-quality SKF bearings and Corteco oil seals are used. SKF bearings are available in the required C3 tolerance ...

Naraku Sports Contra Spring V.2 +1500rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

Naraku Sports Contra Spring V.2 +1000rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS hose clamp - 139QMB/QMA

Oil plug gasket for 139QMB/QMA.

SLS [secondary air system] gasket - 139QMB/A

Oil strainer bolt O-ring - 139QMB/QMA

Timing chain tensioner gasket for 139QMB/QMA.

Cylinder head gasket [50cc = 39mm] - GY6 50cc

This gasket sits in the valve cover in an identical metal plate and seals the crankcase breather. For valve covers with and without SLS.

Right-hand crankcase gasket - GY6 50cc

Gasket for the gearbox cover on GY6 50cc 4-stroke engines.

The Tecnigas Next-R suitable for GY6 50cc 4-stroke and 4-stroke engines Kymco. This exhaust has a good energy yield with relatively low sound. In t...

Some scooters are sent from the factory with two rear shock absorbers. These models mostly use aluminium exhaust systems. These are generally mount...

Oil pump and drive gear for Chinese-built 4-stroke GY6 50ccm 139QMB/QMA engines. This item fits the 22 tooth version. This gear has 47 teeth.

SLS with hose for GY6 50cc exhaust systems with SLS. Often this part is necessary if the mounting bolts have rusted or locked, or the engine is run...

Complete valve cover with connector for 50cc GY6 and Kymco 4-stroke engines. The valve cover is ready to install and supplied as shown. The valve c...

Little end bearing for 12mm gudgeon pin. This size is generally found on CPI, Keeway, Mawi, Longija, Generic engines etc. from 2003 on, as well as ...

139QMB/QMA engines currently have 2 crank variations factory-fitted. The differences are solely in the oil pump drive gear. The crank can be kitted...

Naraku Torque Driver with 2 different linear guide slots. Most torque drivers have curved slots which is not ideal for performance gains but fine f...

V.2 is the latest version of the CNC-machined pulley from NARAKU. This enhanced version now allows you to mount the original variator fan wheel and...

Aluminum Kickstarter [Light] in carbon look suitable for Minarelli and Peugeot engines.

Aluminum Kickstarter [Light] suitable for Minarelli and Peugeot engines.

The Naraku HS-Racing is a well-engineered High Speed variator for Minarelli-based 2-stroke engines with a 16mm tail shaft. The variator comes with ...

Repair kit for Chinese GY6 139QMB/QMA original carburettors. Comes with adjustable needle, needle clip, main jet, pilot jet, float bowl gasket, idl...

Variator back plate.

Base washer for kick-start spindle. Mounts on the outside of the crankcase cover and sits under the circlip.

Kickstarter retaining circlip.

Replacement CDI ignition box fits for Keeway, CPI and Generic models from 2003 on with Euro 2 exhaust certification. AC current / 2 Plug type (Plea...

Carrier sprocket for the variator v-belt pulley fan. The kick-start carrier accompanies the kickstarter sprocket. It sits on the crank in front of ...