Hyosung

Replacement right-hand mirror in original design with E-certification for Hyosung RT, GF and GT (04-06) Naked motorcycles. Cheaper alternative to e...

Replacement left-hand mirror in original design with E-certification for Hyosung RT, GF and GT (04-06) Naked motorcycles. Cheaper alternative to ex...

Dowel pin set for 50cc GY6 engines Delivery contains: 6x dowel pins for M7 (cylinder, cylinder head) 6x dowel pins for M6 (engine cases, crankcase ...

Low-cost, standard brake shoes. Supplied with a set of new shoe springs. Size: 110x25mm Generally for rear brake use, but can be used for front on ...

Fully floating axle with bolt and sleeve for front wheels. Axle length: 215mm, diameter: 10mm. Please check required axle length before ordering, a...

Rubber bushes for engines mounts on GY6 139QMB/QMA engines.

Standard Bosch spark plug with silver electrodes. This spark plug matches the heat value and construction of the original.

Scooter tyre innertube with 90° bent valve for easier pressure checks. Our Tip: Always replace the innertube when changing the tyre. Suitable for ...

PRO-X is the most cost-effective shock in the YSS range. Double-action damping system with adjustable spring preload (tool included). Progressive d...

Malossi strengthened counterpressure springs for rear Malossi convertors, Peugeot Type. Counterpressure springs place the drive belt under tension,...

Naraku Sports Contra Spring V.2 +2000RPM The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS Exhaust system gasket - 130QMB/A

SLS [secondary air system] gasket - 139QMB/A

Cylinder base gasket - GY6 50cc

Crankcase cover gasket [10”-669mm] - GY6 50cc

Exhaust system with SLS connector in OEM quality. Only for vehicles with a factory-fitted SLS (see image 2).

The oil plug also measures the oil level and there is a measuring gauge on the dip stick, attached to the underside of the plug. Check item to be r...

Naraku High Performance clutch bell with patented R-Vent system for more fresh air over the clutch. Prevents wear and loss of friction. Lower opera...

Plastic fan wheel for variators on GY6 50cc 139QMB/QMA engines. Belt damage is caused by too much heat in the drive area. For this reason, the fan ...

O-ring for isolators and intake manifolds. The isolator sits between the carb and the intake manifold and often causes poor engine running as a res...

NARAKU replacement piston set for 47mm cylinders. The piston has a CNC-machined oil grooves for enhanced lubrication at the piston skirt. The pisto...

Little end bearings for Minarelli/Morini engines with 10mm gudgeon pins.

Air cut-off valve. This valve sits on the side of the carburettor and richens the mixture somewhat to avoid the engine running too lean.

Fan cover for 50cc GY6 139QMB/QMA engines. Includes a cover cap with hole for checking the ignition timing.

This isolator sits between the intake manifold and the cylinder head and can often cause poor revving and engine running when it no longer seals pr...

Wedge for positioning the alternator rotor on the crankshaft. lenght=13mm, wide=3mm, high=2,5mm

Naraku Sport-o racing clutch. Solid sports clutch that engages 1500-2000 rpm higher than standard, meaning better drive and traffic light starts. K...

Polini EVO II Speed Bell is lighter and more revvy than the previous model. The single-piece clutch bell is CNC-machined from a single block, unlik...

Naraku Sports Contra Spring V.2 2 Pack, +1000, +1500 rpm The current version of the Naraku counter pressure spring uses a modified alloy spring pro...

Set of 3 replacement sliding shoes for variator plates.

Standard replacement drive belt suitable for vehicles with 10” wheels. Dimensions: 669-18-30