Italjet

Replacement bolts for the internal rotor ignition systems from Malossi for scooters with Piaggio AC or Minarelli engines.

Innovative intake manifold in extreme heat and fuel-resistant Viton from the Malossi Racing MHR series. Rubber can be rotated in the aluminium base...

Malossi MHR intake manifold with short opening and straight connection. 21/24.5mm variant has a 21mm opening and the 24.5mm carb connection for MHR...

Malossi MHR intake manifold with short opening and straight connection. 22/28mm variant has a 22mm opening and the 28mm carb connection for PHBG 15...

High rev bearing sets from Malossi up to high-end tuned Piaggio engines. Outer ring reduced to 10.8mm for better lubrication. Ball bearings with 8x...

Sporty scooter tyre from Heidenau with K63 profile. The K63 tyre is characterised by its top mileage and convincing handling characteristics. Very ...

Malossi intake manifold with short opening and angled connection. 22/28mm variant has a 22mm opening and the 28mm connection has the width of the o...

Malossi intake manifold with short opening and angled connection. 20.5/23mm variant has a 20mm opening and the 23mm connection has the width of the...

Innovative intake manifold in extreme heat and fuel-resistant Viton from the Malossi Racing MHR series. Rubber can be rotated in the aluminium base...

Carrier sprocket that matches the dimensions of the original.

Fan cover, right-hand side for scooters with Piaggio AC engines.

Air filter for 50, 125 and 150cc Vespa ET4 scooters from ’99-’05. 100% match of the original. Filter suitable for the following vehicles: ADIVA...

The Heidenau K66 reinforced is a long-life all-weather tyre. The profile blocks are specially cut for top handling performance. The channels guaran...

Naraku heavy-cheeked racing crank increases the pre-compression in the cases for improved filling. The extra inertia improves performance and the p...

Great quality Naraku crankshaft for scooters with water- or air-cooled Piaggio engines. Corresponds to the original crank dimensions. Delivery incl...

Naraku heavy-cheeked HPC racing crank increases the pre-compression in the cases for improved filling. The extra inertia improves performance and t...

Malossi racing clutch spring set for original clutches in 3 spring weights. black = light (touring) White = medium (sport) Yellow = hard (racing) h...

The finest clutch bell you could use, with cooling vents for improved heat dispersion and reduced slip on the bell and plates.

Thanks to its modern, open allround profile, the Heidenau K66 Snowtex winter tyre for scooters guarantees great handling on cold, wet surfaces. Tha...

Thanks to its modern, open allround profile, the Heidenau K66 Snowtex winter tyre for scooters guarantees great handling on cold, wet surfaces. Tha...

Woodruff key with blunted edges for scooters with 50-180cc Piaggio 2-stroke engines. length=12mm, wide=3mm, high=5mm

Easy to tune variator from Top Racing. The variator can be used with original belt. Supplied with unrestricted vario sleeve and 3 sets high quality...

Arreche 23.5mm sealing ring for carbs with threaded flange.

Arreche 25mm sealing ring for carbs with threaded flange.

Polini reinforced transmission cover, ideal for tuning above 70cc. The standard cover allows the gearshaft to sit in a recess and is only lubricate...

Polini reinforced transmission cover, ideal for tuning above 70cc. The standard cover allows the gearshaft to sit in a recess and is only lubricate...

Naraku double-layer air filter element for original air boxes. For standard or lightly-tuned engines. Check the product image to ensure you get the...

Complete replacement indicators for Aprilia Scarabeo, SR50 and Italjet Torpedo scooters. The turn signal corresponds to the original part. Replaces...

Complete replacement indicators for Aprilia Scarabeo, SR50 and Italjet Torpedo scooters. The turn signal corresponds to the original part. Replaces...

Low-cost scooter exhaust system in black with silver heat guard for all models with Piaggio engines. Very good fit and ideal for those looking for ...

Having a large intake manifold makes little difference without the correct reed block. This low-cost racing reed block makes for a clear path and g...

Top quality cylinder kit by Naraku. An extra emphasis was put on the piston quality. The Naraku piston has a molybdenum coating, so that cylinder a...

Very large inlet cross section from the patented V-Force 3 system by Tassinari in a Top Performances reed block. Rather than the standard 4 valves,...

Replacement membrane block with plastic membranes. This is safer should they break off into the cylinder, where they will simply be spat out the ex...

Replacement membrane block with glass fibre membranes. This is safer should they break off into the cylinder, where they will simply be spat out th...

Solid aluminium machined riser kit. The lift kit is 40mm. The scooter looks great and you get a sportier seating position. An absolute must for all...

Solid aluminium machined riser kit. The lift kit is 40mm. The scooter looks great and you get a sportier seating position. An absolute must for all...

Solid aluminium machined riser kit. The lift kit is 40mm. The scooter looks great and you get a sportier seating position. An absolute must for all...

Solid aluminum machined height adjuster kit. This height adjuster kit is 38mm. The strut can be mounted using the four holes onto the shock absorbe...

Licenced replica of the English Amal carburettor from Arreche. Available in various sizes. 16mm easy to tune for standard cylinders and tuned 50cc ...

Aluminium-machined height adjuster set. 38mm, two fitment holes, allows for great adjustability and gives a sporty position. A must for styling fan...

Aluminium-machined height adjuster set. 38mm, two fitment holes, allows for great adjustability and gives a sporty position. A must for styling fan...

Aluminium-machined height adjuster set. 38mm, two fitment holes, allows for great adjustability and gives a sporty position. A must for styling fan...

Aluminium-machined height adjuster set. 38mm, two fitment holes, allows for great adjustability and gives a sporty position. A must for styling fan...

Aluminium-machined height adjuster set. 38mm, two fitment holes, allows for great adjustability and gives a sporty position. A must for styling fan...

Number plate which is positioned centrally behind the rear wheel. This was seen on standard piaggio scooters. Made of brushed stainless steel, the ...

Complete set for shaft seals for Piaggio engines. Contains 7 seals.

Low-cost lower seal for membrane blocks for Piaggio and Peugeot horizontal 50cc 2-stroke engines. Please note: generally an upper and lower seal is...