Motofino

Primary gear shaft for Chinese 125/150cc scooters with the 152/157QMI engine. This is where the clutch is mounted. This gear has 15 teeth as per or...

Gearbox output shaft - long version. For rear wheel mounting. Total length: 197mm, used for vehicles with additional swinging arm on the right-hand...

Isolator between carb and intake manifold.

Brake light switch for rear disc brakes on GY6 50/125/150cc Chinese-built scooters with rear disc brakes.

Original intake manifold for all GY6 125/150cc 152/157QMI engines. Delivery includes clamp and O-ring. 24mm opening.

Repair kit for Chinese GY6 139QMB/QMA original carburettors. Comes with adjustable needle, needle clip, main jet, pilot jet, float bowl gasket, idl...

Rear brake cable Rusted, seized or sticking brake cables can be a safety risk. If you notice any of these symptoms, it’s time to get it sorted. S...

Folding kickstarter lever for 125/150cc GY6 4-stroke Chinese-built engines.

Standard CDI ignition unit as factory-fitted.

Complete timing chain tensioner suitable for 125/150cc GY6 Chinese-built 4-stroke engines. Delivery includes tensioner tool, which is only to be us...

Crank seals for 125/150cc GY6 4-stroke engines. Set contains 4 seals for left and right-hand side, as well as for the gearbox output shaft.

Replacement aftermarket clutch bell. Already blued clutch bells tend mean slipping and deforming of the plates. This means the bell cannot run true...

Low-cost standard brake disc in original quality. This brake disc has 3 mounting points and a diameter of 180mm. For front and rear disc brakes wit...

Aftermarket front brake disc. 3-point mounting and external diameter of 220mm. Supplied as shown.

Complete front brake calliper for 125/150cc Chinese-built GY6 scooters, incl. brake pads. Those callipers are factory-fitted as either 1 or 2 pisto...

Variator back plate.

Base washer for kick-start spindle. Mounts on the outside of the crankcase cover and sits under the circlip.

Kickstarter retaining circlip.

Replacement CDI ignition box fits for Keeway, CPI and Generic models from 2003 on with Euro 2 exhaust certification. AC current / 2 Plug type (Plea...

Carrier sprocket for the variator v-belt pulley fan. The kick-start carrier accompanies the kickstarter sprocket. It sits on the crank in front of ...

Front outer v-belt pulley. Suitable for GY6 139QMB/QMA engines, Kymco 4-stroke engines and Kymco models with horizontal cylinders. Outside diameter...

This plastic spacer prevents the kickstarter spring from rubbing against the crankcase cover, making it easier to turn over.

Kickstarter recoil spring.

Oil strainer bolt for GY6 50ccm 139QMB/QMA and 125/150ccm 152/157QMI 4-stroke engines.

Oil strainer 50cc GY6 139QMB/QMA engines and 125/150cc GY6 152/157QMI.

Oil strainer spring for all 50cc GY6 139QMB/QMA 4-stroke engines and 125/150cc 152/157QMI.

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Baotian ignition system for approx. 30mph restricted vehicles. Road legal. Not suitable for derestricting vehicles as no Vehicle Type Approval. Att...

Kickstart pinion gear clip for GY6 50cc 139QMB/QMA

Kick-start sprocket with very strong teeth to deal with heavy loads, as they transfer the power from the kick-start to the crank. Many starting iss...

Complete timing chain tensioner for 50cc GY6 4-stroke engines. Tensioner gasket not included and should be ordered separately.

Complete hydraulic system for disc brakes on GY6 125/150cc Chinese-built scooters with rear disc brakes. Set includes: hand brake cylinder with lev...

Hand brake cylinder with lever and brake light switch for front disc brake systems. Fits all standard 125/150cc GY6 Chinese-built scooter handlebars.

This brake system consists of a hand brake cylinder (hand brake pump) with lever, hose, calliper with pads and brake light switch. The brake system...

Steel-braided hoses for 125/150cc Chinese 4-stroke scooters with rear disc brake. Steel braided hoses are brake hoses, surrounded by a woven steel ...

Rear brake line for 125 and 150cc 4-stroke Chinese scooters with rear disc brake. The design matches that of the standard system. For added assuran...

Complete kit of all variator components for all 125cc or 150cc GY6 4-stroke Chinese-built 152/157QMI engines. The kit contains a variator, a set of...

Complete replacement engine for Chinese-built 4-stroke scooters with 10” wheels (3.5x10 / 3.00x10 / 90/90-10 etc.). As a result of the time saved...

Complete rocker mechanism including all individual parts ready fitted. For all GY6 125/150cc 152/157QMI engines.

Valve cover for cylinder heads without SLS. For all GY6 125/150cc 152/157QMI engines.

Complete crank with bearings. Standard replacement crank for all 125 and 150cc GY6 4-stroke engines e.g.: Baotian, Rex, Peugeot Zoom Up, Keeway etc.

The starter clutch carrier wheel transfers the power from the starter to the clutch. If the teeth on the e-starter or the clutch are damaged, they ...

Malossi BigBore cylinder with 52mm bore in aluminium with hard chromed liner. The bore = 87.9cc capacity. Original head may be retained according t...

Of Tecnigas we have a very nice chrome exhaust processed in sport optics in the delivery program. A visual treat with 2-stroke look. Performance-wi...

CNC-machined replacement piston for 52.4mm Naraku cylinder with molybdenum coating. Comes complete with piston rings, oil scraper rings, gudgeon pi...

Complete cylinder gasket set for all 51mm and 52.4mm Naraku 4-stroke cylinder sets Kit contains all necessary gaskets from the base upwards and is ...

Complete cylinder gasket set for all 44mm Naraku or 44mm Chinese-built 4-stroke cylinder sets.

Replacement drive belt suitable for GY6 125/150cc engines with short blocks. Dimensions: 735-20-30