REX (Jinan Qingqi, Shenke)

Malossi MHR intake manifold with short opening and straight connection. 22/28mm variant has a 22mm opening and the 28mm carb connection for MHR Tea...

Malossi 45° MHR Racing performance reed block with 2 single-piece reeds. 0.3mm for improved gas flow. Straight from the Malossi MHR racing departm...

Malossi strengthened counterpressure springs for rear Malossi convertors, Peugeot Type. Counterpressure springs place the drive belt under tension,...

The big brother of the 50cc cylinder kit: the Airsal 70cc is a high torque sports cylinder with great low down power. Delivery includes: gasket set...

Malossi robust, high compression MHR Racing crank with 39.2mm standard stroke and 80mm standard rod length, designed for 10mm gudgeon pins. Safe up...

Naraku Sports Contra Spring V.2 +200rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better res...

Naraku Sports Contra Spring V.2 +2000RPM The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS Exhaust system gasket - 130QMB/A

SLS [secondary air system] gasket - 139QMB/A

Cylinder base gasket - GY6 50cc

Crankcase cover gasket [10”-669mm] - GY6 50cc

The bigger brother to the Naraku Racing Variator: the Naraku High Speed Racing V.2. The variator surface has been blast-hardened with glass beads, ...

M10x1 nut for clutch bells for all Minarelli and Minarelli-based engines.

Exhaust system with SLS connector in OEM quality. Only for vehicles with a factory-fitted SLS (see image 2).

Brake pad set for single piston callipers on Chinese-built 50/125/150cc 4-stroke machines. Unfortunately there is no information regarding which pa...

The oil plug also measures the oil level and there is a measuring gauge on the dip stick, attached to the underside of the plug. Check item to be r...

Naraku HD (Heavy Duty) crank main bearing set. Set contains left and right crank bearings in metal cage and relevant shaft seals. Only bearings wit...

Buzzetti universal 3-point puller for alternator rotors. The 3 screws included in the delivery are simply screwed into the holes in the rotor. Then...

Naraku High Performance clutch bell with patented R-Vent system for more fresh air over the clutch. Prevents wear and loss of friction. Lower opera...

Complete wheel-mounted speedo drive for 125/150cc 4-stroke Chinese-built scooters. As there are various types of drive fitted to these machines, pl...

Starter motor for GY6 125/150cc, supplied with connector cable.

Complete air filter box for 125/150cc Chinese GY6 4-stroke scooters. As there are so many variations to this scooter, please check the product phot...

Rear brake calliper, incl. brake pads. Suitable for vehicles with rear disc brakes.

As original kick-start shaft. A defective shaft is often the cause of sticking kick-starts, or noises when starting.

Plastic fan wheel for variators on GY6 50cc 139QMB/QMA engines. Belt damage is caused by too much heat in the drive area. For this reason, the fan ...

Complete speedo cable for GY6 125/150cc Chinese-built 4-stroke scooters. Length: 96cm. For added assurance, please check the original against the p...

This brake cylinder assembly is suitable for 125 and 150cc GY6 4-stroke Chinese-built scooters with rear brake discs. Supplied complete with hand l...

Naraku racing CDI for improved performance and speed. Simply swap for the original unit. You can get rid of your restricted factory-fitted CDI. Att...

O-ring for isolators and intake manifolds. The isolator sits between the carb and the intake manifold and often causes poor engine running as a res...

Cost-effective replacement belt for everyday use. Good flex and outstanding grip and can easily be used in lightly tuned engines. Size: 738-16.5

Complete, pre-assembled clutch unit consisting of a rear converter torque driver, torque spring, clutch housing and clutch shoes. A defective clutc...

Throttle cable for 125/150cc 4-stroke Chinese-built scooters. The throttle cable has a length of 212cm and fits almost every 125cc and 150cc model....

NARAKU replacement piston set for 47mm cylinders. The piston has a CNC-machined oil grooves for enhanced lubrication at the piston skirt. The pisto...