Roketa

Jumpy drive and bad power transfer are usually signs that the clutch plates are either worn or glazed. The only solution is to change the plates. W...

Side stand for 125/150cc Chinese-built 4-stroke scooters. Fits most vehicles. As there are various bodywork designs, in some cases manufacturers wi...

Kickstarter shaft [63mm / 21mm] - GY6 50cc

Low-cost aftermarket kickstarter shaft [semi-circle], for Kymco 2- and 4-stroke 50/125cc engines. There are different shaft lengths for different c...

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Airsal 165cc [Sport] cylinder gasket set - GY6 152/157 QMI

Piston ring set Airsal 165cc [Sport] - GY6 152/157 QMI

Airsal piston kit 165cc [Sport] - GY6 152/157 QMI

Airsal high-performance cylinder kit 165cc capacity, with gasket set, piston, rings etc. Hard chromed liner. 165cc gives engines notably better tor...

Crankshaft in high quality manufactured in Europe for Chinese 50cc 4-stroke engines and 4-stroke 50cc Kymco. High quality con rod tin much better q...

Long gearbox output shaft for vehicles with a swinging arm on the right-hand side. Mounted through the swing arm. These models generally have twin ...

Speed Belt by Polini. This v-belt features an aramid weave that makes it elastic and highly durable. Without doubt, one of the best v-belts in our ...

Malossi reinforced counter pressure torque spring - yellow = super strong

Airsal 150cc [Sport] cylinder gasket set Racing - GY6 152/157 QMI

Piston ring set suitable for the Airsal 150cc sport cylinder kit for GY6 152/157 QMI/QMJ.

Airsal piston kit 150cc [Sport] - GY6 152/157 QMI

Airsal high-performance cylinder kit 150cc capacity, with gasket set, piston, rings etc. Hard chromed liner. 150cc gives 125cc engines notably bett...

Naraku carburettor repair kit for 50-90cc carbs. Comes with adjustable needle, needle clip, 80 main jet, pilot jet, float bowl gasket, idle jet, mi...

Timing chain tensioner gasket for GY6 125/150cc.

Cylinder base gasket - GY6 125/150cc

Valve cover gasket [rubber] - GY6 125/150cc

Crankcase cover gasket for Chinese-built scooters with GY6 125/150cc engines. The gasket is solely for the short engine blocks of the 4-stroke mode...

Mid-crankcase gasket for GY6 125/150cc engines.

Gasket for the gearbox cover on GY6 125/150cc 4-stroke engines.

Right-hand crankcase gasket - GY6 125/150cc

Set of 3 sliders for Malossi Multivar variators. Sliders should be replaced to avoid damage. Not suitable for Piaggio MHR variators.

Naraku Sports Contra Spring V.2 +1500rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

Naraku Sports Contra Spring V.2 +1000rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS hose clamp - 139QMB/QMA

Oil plug gasket for 139QMB/QMA.

SLS [secondary air system] gasket - 139QMB/A

Oil strainer bolt O-ring - 139QMB/QMA

Timing chain tensioner gasket for 139QMB/QMA.

Cylinder head gasket [50cc = 39mm] - GY6 50cc

This gasket sits in the valve cover in an identical metal plate and seals the crankcase breather. For valve covers with and without SLS.

Right-hand crankcase gasket - GY6 50cc

Gasket for the gearbox cover on GY6 50cc 4-stroke engines.

The Tecnigas Next-R suitable for GY6 50cc 4-stroke and 4-stroke engines Kymco. This exhaust has a good energy yield with relatively low sound. In t...

Some scooters are sent from the factory with two rear shock absorbers. These models mostly use aluminium exhaust systems. These are generally mount...

Oil pump and drive gear for Chinese-built 4-stroke GY6 50ccm 139QMB/QMA engines. This item fits the 22 tooth version. This gear has 47 teeth.

SLS with hose for GY6 50cc exhaust systems with SLS. Often this part is necessary if the mounting bolts have rusted or locked, or the engine is run...

Valve cover for GY6 125/150cc 4-stroke 152/157QMI engines WITH SLS system. The valve cover is ready to install and delivered as shown. Valve cover ...

Complete valve cover with connector for 50cc GY6 and Kymco 4-stroke engines. The valve cover is ready to install and supplied as shown. The valve c...

139QMB/QMA engines currently have 2 crank variations factory-fitted. The differences are solely in the oil pump drive gear. The crank can be kitted...

Replacement drive belt suitable for GY6 125/150cc engines with long blocks. Dimensions: 835-20-30

Rubber stops for the engine rockers. 2 items generally required when changing out.

Rubber centre stand stop for 125/150cc Chinese-built scooters. Suitable for most scooter types, but please check image against the original item.

Complete intake hose for the crankcase cover, with clamp. Suitable for crankcase covers on 125/150cc GY6 4-stroke engines.