RS Ultima

Naraku sports clutch. Solid sports clutch that engages 1500-2000rpm higher than standard, meaning better drive and traffic light starts. Fiber rein...

Petrol cap centre fairing in silver. PLEASE NOTE THIS PART DOES NOT FIT THE PEUGEOT V-CLIC.

Black pillion cover / petrol cap surround centre fairing for QT-9. PLEASE NOTE THIS PART DOES NOT FIT THE PEUGEOT V-CLIC.

Lower left side fairing in silver. PLEASE NOTE THIS PART DOES NOT FIT THE PEUGEOT V-CLIC.

Silver coloured headlight surround fairing. PLEASE NOTE THIS PART DOES NOT FIT THE PEUGEOT V-CLIC.

Lower front cover fairing in Black. PLEASE NOTE THIS PART DOES NOT FIT THE PEUGEOT V-CLIC.

Dowel pin set for 50cc GY6 engines Delivery contains: 6x dowel pins for M7 (cylinder, cylinder head) 6x dowel pins for M6 (engine cases, crankcase ...

Low-cost, standard brake shoes. Supplied with a set of new shoe springs. Size: 110x25mm Generally for rear brake use, but can be used for front on ...

Fully floating axle with bolt and sleeve for front wheels. Axle length: 215mm, diameter: 10mm. Please check required axle length before ordering, a...

Rubber bushes for engines mounts on GY6 139QMB/QMA engines.

Well priced 3 shoe replacement clutch in OEM-quality.

Carbon Power reeds for original reed blocks for scooters with Minarelli engines. Kinder to engines if they break-up. 2x carbon reeds supplied. Chea...

Rectifier / Controller changes the AC into DC on a 12V board. This prevents bulbs from burning out. Exposure to high temperatures means bulbs often...

Latest variator technology from Polini for untuned 50cc engines for improved acceleration and higher top speed. Polini evo sliders make for better ...

Scooter tyre innertube with 90° bent valve for easier pressure checks. Our Tip: Always replace the innertube when changing the tyre. Suitable for ...

Naraku High Performance clutch bell with patented R-Vent system for more fresh air over the clutch. Prevents wear and loss of friction. Lower opera...

Complete braking system with level and rear brake light switch for 125/150cc Chinese 4-stroke scooters with rear drum brakes. The fitting has a thr...

PRO-X is the most cost-effective shock in the YSS range. Double-action damping system with adjustable spring preload (tool included). Progressive d...

Malossi MHR intake manifold with short opening and straight connection. 22/28mm variant has a 22mm opening and the 28mm carb connection for MHR Tea...

Malossi 45° MHR Racing performance reed block with 2 single-piece reeds. 0.3mm for improved gas flow. Straight from the Malossi MHR racing departm...

Malossi strengthened counterpressure springs for rear Malossi convertors, Peugeot Type. Counterpressure springs place the drive belt under tension,...

Malossi large pore sports air filter. Great filtering performance in fire-resistant foam.For optimal performance when used on the road, we recommen...

Naraku Sports Contra Spring V.2 +200rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better res...

Naraku Sports Contra Spring V.2 +2000RPM The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS Exhaust system gasket - 130QMB/A

SLS [secondary air system] gasket - 139QMB/A

Cylinder base gasket - GY6 50cc

Crankcase cover gasket [10”-669mm] - GY6 50cc

The bigger brother to the Naraku Racing Variator: the Naraku High Speed Racing V.2. The variator surface has been blast-hardened with glass beads, ...

M10x1 nut for clutch bells for all Minarelli and Minarelli-based engines.

The oil plug also measures the oil level and there is a measuring gauge on the dip stick, attached to the underside of the plug. Check item to be r...

Buzzetti universal 3-point puller for alternator rotors. The 3 screws included in the delivery are simply screwed into the holes in the rotor. Then...

Naraku High Performance clutch bell with patented R-Vent system for more fresh air over the clutch. Prevents wear and loss of friction. Lower opera...

Starter motor for GY6 125/150cc, supplied with connector cable.

As original kick-start shaft. A defective shaft is often the cause of sticking kick-starts, or noises when starting.

Plastic fan wheel for variators on GY6 50cc 139QMB/QMA engines. Belt damage is caused by too much heat in the drive area. For this reason, the fan ...

Naraku racing CDI for improved performance and speed. Simply swap for the original unit. You can get rid of your restricted factory-fitted CDI. Att...

O-ring for isolators and intake manifolds. The isolator sits between the carb and the intake manifold and often causes poor engine running as a res...

This bush sits in the crankcase cover and carries the kickstarter shaft. It can quickly become worn and cause kickstarter issues and, in extreme ca...

Complete, pre-assembled clutch unit consisting of a rear converter torque driver, torque spring, clutch housing and clutch shoes. A defective clutc...

Throttle cable for 125/150cc 4-stroke Chinese-built scooters. The throttle cable has a length of 212cm and fits almost every 125cc and 150cc model....

NARAKU replacement piston set for 47mm cylinders. The piston has a CNC-machined oil grooves for enhanced lubrication at the piston skirt. The pisto...

Plastic fan wheel air cooling for CPI, Keeway, Generic, Mawi, Longija and other Chinese-built 2-stroke engines.

Little end bearings for Minarelli/Morini engines with 10mm gudgeon pins.

Complete tail light bulbs included. E-certificate. Suitable for all Chinese-built 4-stroke vehicles with vehicle design like the Rex RS450, Baotian...