Schwinn

Malossi reinforced counter pressure torque spring - yellow = super strong

Airsal 150cc [Sport] cylinder gasket set Racing - GY6 152/157 QMI

Piston ring set suitable for the Airsal 150cc sport cylinder kit for GY6 152/157 QMI/QMJ.

Airsal piston kit 150cc [Sport] - GY6 152/157 QMI

Airsal high-performance cylinder kit 150cc capacity, with gasket set, piston, rings etc. Hard chromed liner. 150cc gives 125cc engines notably bett...

Naraku carburettor repair kit for 50-90cc carbs. Comes with adjustable needle, needle clip, 80 main jet, pilot jet, float bowl gasket, idle jet, mi...

Timing chain tensioner gasket for GY6 125/150cc.

Cylinder base gasket - GY6 125/150cc

Valve cover gasket [rubber] - GY6 125/150cc

Crankcase cover gasket for Chinese-built scooters with GY6 125/150cc engines. The gasket is solely for the short engine blocks of the 4-stroke mode...

Mid-crankcase gasket for GY6 125/150cc engines.

Gasket for the gearbox cover on GY6 125/150cc 4-stroke engines.

Right-hand crankcase gasket - GY6 125/150cc

Set of 3 sliders for Malossi Multivar variators. Sliders should be replaced to avoid damage. Not suitable for Piaggio MHR variators.

Naraku Sports Contra Spring V.2 +1500rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

Naraku Sports Contra Spring V.2 +1000rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

SLS hose clamp - 139QMB/QMA

Oil plug gasket for 139QMB/QMA.

SLS [secondary air system] gasket - 139QMB/A

Oil strainer bolt O-ring - 139QMB/QMA

Timing chain tensioner gasket for 139QMB/QMA.

Cylinder head gasket [50cc = 39mm] - GY6 50cc

This gasket sits in the valve cover in an identical metal plate and seals the crankcase breather. For valve covers with and without SLS.

Right-hand crankcase gasket - GY6 50cc

Mid-crankcase gasket. This gasket seals the left and right hand sides together. Required when changing the crank or completely splitting the cases.

Gasket for the gearbox cover on GY6 50cc 4-stroke engines.

The Tecnigas Next-R suitable for GY6 50cc 4-stroke and 4-stroke engines Kymco. This exhaust has a good energy yield with relatively low sound. In t...

Some scooters are sent from the factory with two rear shock absorbers. These models mostly use aluminium exhaust systems. These are generally mount...

Oil pump and drive gear for Chinese-built 4-stroke GY6 50ccm 139QMB/QMA engines. This item fits the 22 tooth version. This gear has 47 teeth.

SLS with hose for GY6 50cc exhaust systems with SLS. Often this part is necessary if the mounting bolts have rusted or locked, or the engine is run...

Valve cover for GY6 125/150cc 4-stroke 152/157QMI engines WITH SLS system. The valve cover is ready to install and delivered as shown. Valve cover ...

Complete valve cover with connector for 50cc GY6 and Kymco 4-stroke engines. The valve cover is ready to install and supplied as shown. The valve c...

139QMB/QMA engines currently have 2 crank variations factory-fitted. The differences are solely in the oil pump drive gear. The crank can be kitted...

Replacement drive belt suitable for GY6 125/150cc engines with long blocks. Dimensions: 835-20-30

Standard brake shoes. Also included: 2 new springs. Performance and construction as per original item. Dimensions: 110mmx25mm For rear drum brakes ...

Rubber stops for the engine rockers. 2 items generally required when changing out.

Rubber centre stand stop for 125/150cc Chinese-built scooters. Suitable for most scooter types, but please check image against the original item.

Complete intake hose for the crankcase cover, with clamp. Suitable for crankcase covers on 125/150cc GY6 4-stroke engines.

Bolt and nut set for GY6 125/150cc engines. Set contains almost all bolts, oil draining plugs, nuts, cylinder studs etc. Ordering individual engine...

Outer v-belt pulley for GY6 125/150cc 4-stroke Chinese-built engines.

Naraku Torque Driver with 2 different linear guide slots. Most torque drivers have curved slots which is not ideal for performance gains but fine f...

V.2 is the latest version of the CNC-machined pulley from NARAKU. This enhanced version now allows you to mount the original variator fan wheel and...

Original fan cover for 125/150cc GY6 4-stroke Chinese-built engines.

Alternator stator for GY6 125/150cc machines. There are many variations of this alternator of these engines. They can however be quite easy to iden...

Complete air filter element [type 1] for 125/150cc Chinese GY6 4-stroke scooters. As there are so many variations to this scooter, please check the...

Complete shock unit for 125/150cc Chinese-built 4-stroke scooters, chromed. Non-adjustable. Length: 335mm, please ensure you are ordering the corre...

Complete aftermarket piston for GY6 150 4-stroke Chinese-built models. Includes gudgeon pin, piston, piston rings, oil scraper rings and gudgeon pi...