Vento

Naraku piston kit [58.5mm / 160cc] 4-stroke

Clutch bell for GY6, Kymco, Honda, Malaguti Maxi-scooters. OEM-quality and great alternative to original items. Juddery starts or discoloured clutc...

Gearbox output shaft (wheel shaft) for GY6 125/150cc 4-stroke Chinese-built engines. This version is for vehicles with a rear drum brake. Shaft len...

Replacement crank for CPI, Keeway, Generic, MaWi scooters and all 2-stroke Chinese-built vehicles with Minarelli-based Euro 2 engines. The crank is...

Innertube with 45° angled valve for smaller sized wheels. Our tip: Always replace innertubes when changing tyres.

Very well-engineered and robust sports clutch from Malossi. Reinforced clutch springs and weight saving on the plates means better drive from light...

Centre stand for 125/150cc Chinese-built 4-stroke scooters. There are differences between the location of the spring in individual centre stands, s...

Jumpy drive and bad power transfer are usually signs that the clutch plates are either worn or glazed. The only solution is to change the plates. W...

Side stand for 125/150cc Chinese-built 4-stroke scooters. Fits most vehicles. As there are various bodywork designs, in some cases manufacturers wi...

Kickstarter shaft [72mm / 24mm] - GY6 50cc

Airsal 165cc [Sport] cylinder gasket set - GY6 152/157 QMI

Piston ring set Airsal 165cc [Sport] - GY6 152/157 QMI

Airsal piston kit 165cc [Sport] - GY6 152/157 QMI

Airsal high-performance cylinder kit 165cc capacity, with gasket set, piston, rings etc. Hard chromed liner. 165cc gives engines notably better tor...

Innovative intake manifold in extreme heat and fuel-resistant Viton from the Malossi Racing MHR series. Intake manifold features 30mm opening, maki...

Malossi 4 reed racing reed block. 0.3mm thick reeds give great power when used with the Malossi Big Valve blocks. Malossi offers 2 additional membr...

Malossi MHR intake manifold with short opening and straight connection. 22/24.5mm variant has a 22mm opening and a 24.5mm carb carb connection 19-2...

High-quality, but cost-effective aftermarket piston for original cylinders from Italian piston specialists Meteor. The set contains a piston, gudge...

High-quality, but cost-effective aftermarket piston for original cylinders from Italian piston specialists Meteor. The set contains a piston, gudge...

Reeds for original factory reed block with carbon membranes. These cause less damaged to the engine should the reed petals break up than metal alte...

Airsal 150cc [Sport] cylinder gasket set Racing - GY6 152/157 QMI

Piston ring set suitable for the Airsal 150cc sport cylinder kit for GY6 152/157 QMI/QMJ.

Airsal piston kit 150cc [Sport] - GY6 152/157 QMI

Airsal high-performance cylinder kit 150cc capacity, with gasket set, piston, rings etc. Hard chromed liner. 150cc gives 125cc engines notably bett...

Polini Air Speed variator pulley, great upgrade for the original due to design producing increase cooling. Suitable for 16mm shafts only.

Timing chain tensioner gasket for GY6 125/150cc.

Cylinder base gasket - GY6 125/150cc

Valve cover gasket [rubber] - GY6 125/150cc

Crankcase cover gasket for Chinese-built scooters with GY6 125/150cc engines. The gasket is solely for the short engine blocks of the 4-stroke mode...

Mid-crankcase gasket for GY6 125/150cc engines.

Gasket for the gearbox cover on GY6 125/150cc 4-stroke engines.

Right-hand crankcase gasket - GY6 125/150cc

Airsal cylinder head 70cc [T6-Racing] - CPI, Keeway E2

Airsal piston kit 50cc [T6-Racing] - CPI, Keeway E2

Airsal cylinder head 50cc [T6-Racing] - CPI, Keeway E2

Set of 3 sliders for Malossi Multivar variators. Sliders should be replaced to avoid damage. Not suitable for Piaggio MHR variators.