Vento

Complete lock barrel with 2 spare keys for Chinese-built 125/150cc 4-stroke scooters. There are various bodywork versions for this ignition barrel....

Gasket for vehicles not fitted with a round exhaust manifold gasket. This is a universal gasket for all flat exhaust manifolds. Solid design and a ...

Very low-cost intake manifold for derestricting the inlet port. This increases the size of the opening to 21mm. This is a must when using a larger ...

NGK is one of the world’s leading spark plug manufacturers. As the factory-fitted choice of many vehicle brands, NGK is there when the spark star...

Complete replacement 24mm carburettor (membrane type) supplied with electric auto choke. Ready to fit and suitable for 125/150cc Chinese-built engi...

Gasket for vehicles not fitted with a round exhaust manifold gasket. This is a universal gasket for all flat exhaust manifolds. Solid design and a ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Complete steering bearing sets including bearing races, ball bearings and locknuts. Bearing set for 27mm fork bridge.

Naraku Sports Contra Spring V.2 +1000 rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better r...

Some scooters are sent from the factory with two rear shock absorbers. These models mostly use aluminium exhaust systems. These are generally mount...

Aftermarket carburettor for all 2-stroke scooters with 1E40QMB engines. Minarelli replica air-cooled. Comes with electric choke. Note: In rare case...

39mm clutch nut M28x1 (central nut under the clutch bell). Suitable for Minarelli, Kymco, Peugeot, Honda engines and many more.

Repair kit for 24mm Naraku carburettors. Comes with adjustable needle, needle clip, main jet, pilot jet, float bowl gasket, idle jet, mix adjuster ...

Kickstarter wheel [carrier] for upright and horizontal Minarelli and Minarelli-based 2-stroke engines as found in CPI, Keeway, Mawi, Longija etc.

Everyday 10 inch tubeless tyre for almost any road conditions and great value for money! This is a true allrounder, offering good grip from its dee...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Cylinder studs including special nuts with M7 thread for securing the cylinder. Set of 4 with nuts. Length: 110mm, nuts are 13mm in length and have...

Replacement indicator glass for various CPI, Keeway, Kymco and Rieju scooters, geared mopeds and ATVs. The turn signal lens corresponds to the orig...

New style oil filler bolt for Minarelli - Red

Complete oil pump for Minarell-based 2-stroke engines from CPI, Keeway, Generic, Mawi, Longija etc. Delivery as shown. Also suitable for Adly 50cc ...

Star washer, mounting/fixing shim for the front belt pulley. The original is not very robust and often breaks. As such, we offer this replacement i...

Naraku HD (Heavy Duty) crank main bearing set. Set contains left and right in metal cage crank bearings and relevant shaft seals. Only bearings wit...

Exhaust manifold gasket for scooters and mopeds with original and tuning/sports exhaust systems with round metal gaskets and dimensions of approx. ...

Low-cost dropping resistor for the lighting system of various 50, 125 and 150cc GY6 4-stroke Kymco and Chinese-built scooters. (5 Watt / 5 Ohm &...

The rectifier/controller changes the voltage from the alternator into the DC for the on board computer, 12V, and keeps the voltage within a certain...

Replacement taillight for various Cagiva, Italjet, Rieju, Voxan, MBK and Yamaha. models. Matches the dimensions of the original. Matches OEM-No.: 8...

Universal throttle sleeve with rubber grip for 125/150cc 4-stroke scooters with GY6 chassis and 22mm diameter handlebars. outer length: 122mm inner...

High-torque 70cc NARAKU cylinder kit with 12mm gudgeon pin. This cylinder kit is not designed to be revvy, but rather it shows its strengths in the...

Rotor puller for removing the alternator flywheel. Our list is based on experience, but you are best to measure threads prior to ordering. Attentio...

High-quality, precision complete gasket set from Spanish gasket specialists Artein Gaskets. The materials are carefully matched to the specific dem...

M12x1.25mm nut for rotor and pulley on the crankshaft. Suitable for all special cranks with M12 thread for Piaggio and Minarelli engines. E.g.: Sta...

Original brake lever for rear brake discs (left-hand brake lever). Suitable for all rear disc brake lever fittings. For added assurance, please che...

Complete alternator for Minarelli-based 2-stroke engines. Suitable for Keeway, CPI, Generic, Longjia, Mawi etc. There are currently 4 different ver...

The kick-start carrier accompanies the kickstarter sprocket. It sits on the crank in front of the crankcase and its teeth can become worn, causing ...

Replacement reed block with steel petals. Suitable for all horizontal Minarelli engines, CPI, Keeway, Generic, Mawi, Longija, Morini engines, April...

Fan cover for CPI, Generic, Keeway, Mawi, Longija right-hand side fans and air-cooled Minarelli engines.

Exhaust manifold gasket for all Chinese-built 4-stroke and Kymco 50cc 4-stroke vehicles. Also suitable for all Naraku 4-stroke tuning cylinder kits...