Yamaha

Naraku unrestricted CDI unit for horizontal Minarelli engines and some 2-stroke Chinese-built models. Not suitable for vehicles with a Ducati ignit...

Naraku small end bearing [HD-Quality] - 10x14x13. Suitable for Minarelli and Morini engines with 10mm gudgeon pin.

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Naraku Sports Contra Spring V.2 +1000 rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better r...

Naraku sport clutch spring set for all Minarelli original and Naraku sports clutches. 3 different graded spring rates supplied, with the rpm value ...

These Speed-up shims influence the length of the variator sleeve. Lengthening can improve acceleration and shortening can increase top end speed. M...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Cylinder studs including special nuts with M7 thread for securing the cylinder. Set of 4 with nuts. Length: 110mm, nuts are 13mm in length and have...

Naraku replacement variator for 50cc horizontal and upright 2-stroke Minarelli engines with 13mm tail shaft. The weight tracks correspond to the or...

Twist Control: an absolute drive innovation from Naraku. Twist Control absorbs the torsion from the converter and even out the loss of power from t...

Naraku HD (Heavy Duty) crank main bearing set. Set contains left and right in metal cage crank bearings and relevant shaft seals. Only bearings wit...

Exhaust manifold gasket for scooters and mopeds with original and tuning/sports exhaust systems with round metal gaskets and dimensions of approx. ...

Rotor puller for removing the alternator flywheel. Our list is based on experience, but you are best to measure threads prior to ordering. Attentio...

M12x1.25mm nut for rotor and pulley on the crankshaft. Suitable for all special cranks with M12 thread for Piaggio and Minarelli engines. E.g.: Sta...

Replacement rubber cap for oil tanks on the 2-stroke Chinese scooters.

Low-cost Racing membrane block in OEM-quality, with 6 reeds. Suitable for all scooters with Piaggio engines from 1999 on. Suitable for all horizont...

Fan wheel in OEM-quality for Minarelli engines. Matches the dimensions of the original.

10mm gudgeon pin circlips from Naraku. Ensure the clip groove is clean and will allow the circlip to seat properly. When installing, we recommend o...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Naraku Sports Contra Spring V.2 +1500rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better re...

Naraku Sports Contra Spring V.2 Pack, +1000, +1500, +2000 rpm The current version of the Naraku counter pressure spring uses a modified alloy sprin...

Outer variator pulley from NARAKU. The pulley corresponds to the shape and dimensions of the original. A cost-effective alternative when pulleys ar...

High-torque 70cc NARAKU cylinder kit. This cylinder kit is not designed to be revvy, but rather it shows its strengths in the lower range. Just abo...

Variator cover gasket suitable for scooters with long Minarelli horizontal engines.

CNC milled Naraku racing clutch bell with 107mm inner diameter. The advantage of using this over the stock bell is the extremely low tolerance and ...

Cost-effective 17.5mm carb from Naraku for Minarelli and Minarelli-based engines (Chinese versions) and horizontal Peugeot engines. Leaves nothing ...

Many scooters from the middle East use different types of carburettor. The carb is a Mikuni copy, but uses an E-choke/cold start valve. You can onl...

Reinforced starter motor freewheel without starter sprocket, from Naraku. The starter mechanism is subjected to higher loading where engines have h...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Well priced racing clutch with lighter clutch shoes. Weight saving means engagement at higher revs. Harder clutch springs. A lower quality sports c...

3 Set of sliders for the Naraku HS and HS-Racing variators for scooters with Minarelli and CPI engines.

Self-locking nut M14x1.50mm for rear wheel shaft (central nut for rear wheel). Also for other Minarelli engines and other models with M14x1.50mm th...

Complete shaft seals for Minarelli engines. Contains 6 seals incl. 2x shaft seals for the rear convertor.

Cylinder gasket set for 50cc air-cooled Minarelli engines. Suitable for original and aftermarket 50cc cylinders.

Replacement star washer / shim from Naraku for securing the outer variator pulleys. Corresponds to the size and design on the original. For all hor...

Replacement piston for the 70cc original and 70cc NARAKU Sports V.2 Cylinder (NK100.31). Delivered as shown with piston rings, gudgeon pin and circ...

Naraku complete alternator stator for horizontal Minarelli engines. Attention! Not for Minarelli engines with Ducati ignitions.

Carbon Power reeds for original reed blocks for scooters with Minarelli engines. Kinder to engines if they break-up. 2x carbon reeds supplied. Chea...