Products

Naraku puller for alternator magnet wheels. Screws onto the existing rotor thread and is tensioned with the tensioning bolt. Light taps with a hamm...

Magneto rotor for alternator Version 1. There are currently 2 different versions of the alternator. Version 1 has a white main connector and 2 cabl...

Alternator with cable connector/plug and Pick-up sensor. These alternators are currently available in 2 different versions. The difference is the i...

Alternator with cable connector/plug and Pick-up sensor. There are currently 2 different versions of this alternator. The difference is the insulat...

Black brake lever for rear brakes on various Keeway and Peugeot scooters.

Brake pads with organic composition. This coating mixture is generally used by the original scooter manufacturers as the OEM part. Solid brake perf...

Standard brake shoe set. 2x new springs supplied. Performance and design match the original. Shoe dimensions: 110x25mm. For rear brake or parking b...

Timing chain for GY6 50cc engines 139QMB/QMA.

Timing chain guide for GY6 50cc engines 139QMB/QMA. This guide sits opposite the chain tensioner and is positioned between the cylinder and the cyl...

Timing chain tensioner guide for GY6 50cc engines 139QMB/QMA.

Complete timing chain tensioner for 50cc GY6 4-stroke engines. Tensioner gasket not included and should be ordered separately.

Timing chain tensioner gasket for 139QMB/QMA.

Adjustable carburettor needle with clip.

Air cut-off valve. This valve sits on the side of the carburettor and richens the mixture somewhat to avoid the engine running too lean. Needle is ...

Air cut-off valve. This valve sits on the side of the carburettor and richens the mixture somewhat to avoid the engine running too lean.

Screw for air cut-off valve and choke plate.

Plastic carburettor cap for all GY6 4-stroke 50cc scooters 139 QMB/QMA

Screw for plastic carburettor cap with collar.

Dragster racing technology. The venture (funnel-shaped) air ducts optimize the airflow to the carburettor and accelerates the volume of air being t...

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Carburettor membrane with slide and adjustable carb needle. Various CVK carbs of the same basic construction are installed on 4-stroke vehicles. Th...

Carburettor diaphragm for original carburettors fitted to the Chinese imported 4 stroke scooters with the 139QMA/QMB. This said, there are still nu...

Metal float bowl with accelerator pump. Suitable for all original and Naraku NK200.01 carbs for GY6 50cc engines 129 QMB/QMA.

Float bowl screw with locking ring.

Standard Naraku carburettor floats for GY6 50cc 139 QMB/QMA.

Float bearing pin.

Float needle valve.

Naraku V.3 carburettor 18.5mm for 50cc 4-stroke scooters. Top quality at an affordable price. No start issues as with Chinese alternatives and good...

Naraku carburettor repair kit for 50-90cc carbs. Comes with adjustable needle, needle clip, 80 main jet, pilot jet, float bowl gasket, idle jet, mi...

Complete 19mm aftermarket carburettor (membrane type) with E-choke and jetting. Ready to mount; suitable for 50 and 80cc 4-stroke engines. This is ...

Carburettor slide spring.

Complete aftermarket carburettor for 4-stroke scooters, with choke. The carburettor is factory-fitted on all 50cc 4-stroke Kymco scooters and many ...

CDI attachment rubber for ignition boxes 37x22mm on 4-stroke Chinese-built scooters.

CDI attachment rubber for ignition boxes 42x23mm on 4-stroke Chinese-built scooters.

E-choke mounting plate.

Affordable replacement clutch shoes suitable for original or midly tuned 50cc engines, matches that of the original clutch dimensions. These are ou...

The most low-cost aftermarket clutch we offer. Even tuned engines can have issues with the clutch. Glazed plates, bad starting or vibrations are in...

The Vicma Evo Racing and Hebo clutches are identical settings in principal. The Hebo differs mainly in the clutch linings. 3 Shoe clutch with varia...