Naraku

Naraku unrestricted CDI unit for horizontal Minarelli engines and some 2-stroke Chinese-built models. Not suitable for vehicles with a Ducati ignit...

This regulator is similar to the NARAKU ignition coil. The controller reaches a significantly higher output than the standard controller by ensurin...

Naraku V.3 carburettor 18.5mm for 50cc 4-stroke scooters. Top quality at an affordable price. No start issues as with Chinese alternatives and good...

Naraku small end bearing [HD-Quality] - 10x14x13. Suitable for Minarelli and Morini engines with 10mm gudgeon pin.

Inlet adapter spacer for horizontal Kymco engines (type SF10). This adapter allows intake manifolds to be used on Minarelli engines. Our race team ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

These Speed-up shims influence the length of the variator sleeve. Lengthening can improve acceleration and shortening can increase top end speed. M...

Naraku Sports Contra Spring V.2 +1000 rpm The current version of the Naraku counter pressure spring uses a modified alloy spring providing better r...

Naraku sport clutch spring set for all Minarelli original and Naraku sports clutches. 3 different graded spring rates supplied, with the rpm value ...

Exhaust manifold gasket with accurate fit to the factory installed exhaust system.

These Speed-up shims influence the length of the variator sleeve. Lengthening can improve acceleration and shortening can increase top end speed. M...

Repair kit for 24mm Naraku carburettors. Comes with adjustable needle, needle clip, main jet, pilot jet, float bowl gasket, idle jet, mix adjuster ...

NARAKU V.2 intake manifold for 50cc GY6 and all GY6-based models, as well as Honda Monkey and Monkey replica engines. Unlike the original part, whi...

Aluminium height adjuster set for rear shocks, from Naraku Performance. This height adjuster set gives scooters a more dynamic look by raising the ...

Cylinder studs including special nuts with M7 thread for securing the cylinder. Set of 4 with nuts. Length: 110mm, nuts are 13mm in length and have...

Naraku replacement variator for 50cc horizontal and upright 2-stroke Minarelli engines with 13mm tail shaft. The weight tracks correspond to the or...

Twist Control: an absolute drive innovation from Naraku. Twist Control absorbs the torsion from the converter and even out the loss of power from t...

Star washer, mounting/fixing shim for the front belt pulley. The original is not very robust and often breaks. As such, we offer this replacement i...

Twist Control: an absolute drive innovation from Naraku. Twist Control absorbs the torsion from the converter and even out the loss of power from t...

Naraku HD (Heavy Duty) crank main bearing set. Set contains left and right in metal cage crank bearings and relevant shaft seals. Only bearings wit...

This Variator sleeve replaces the original factory fitted sleeve and collar. This lifts the restricted power. The scooter will be capable of approx...

Exhaust manifold gasket for scooters and mopeds with original and tuning/sports exhaust systems with round metal gaskets and dimensions of approx. ...

Set of 10 Naraku pilot jets for Dellorto PHBG - PHBD carburettors. You receive a set of 10 with 5mm thread in the following sizes: 30/ 32/ 34/ 36/ ...

Naraku double-layer air filter element for original air boxes. For standard or lightly-tuned engines. Check the product image to ensure you get the...

Replacement studs with M6 thread at both ends, including M6 nuts for use on exhaust manifolds. Complete length: 32mm. set of 2 M6 studs and 2 M6 nu...

High-torque 70cc NARAKU cylinder kit with 12mm gudgeon pin. This cylinder kit is not designed to be revvy, but rather it shows its strengths in the...